Address
304 North Cardinal St.
Dorchester Center, MA 02124
Work Hours
Monday to Friday: 7AM - 7PM
Weekend: 10AM - 5PM
Choose between a Zebra ZC100 LT kit and a ZC300 printer by badge layout, software terms, starter supplies and the connection your desk needs.
This post may contain affiliate links. As an Amazon Associate we earn from qualifying purchases, at no extra cost to you. Learn more.
Start with the ZC100 LT kit if you need a single-sided card printer packaged with design software and starter supplies. Choose the dual-sided ZC300 USB/Ethernet unit if you need automatic printing on both sides or a confirmed network connection, and can arrange software and supplies separately.
The main difference between these purchases is what you receive with the printer. The LT kit names CloudBadging, cards and a ribbon, but leaves the software term and supply quantities unstated. The linked ZC300 identifies its side configuration and connections, but does not establish an included badge design license or starter supplies.
Write down your badge layout and computer requirements before choosing. A single-sided employee photo badge is a different job from a badge with printed instructions on the reverse. If the card must operate a door reader, confirm the required credential and encoding hardware separately.
For either exact purchase, check the current price on Amazon. Compare the full setup you need rather than assume that two products described as Zebra card printers contain the same components.
Package contents in the table follow the linked Amazon descriptions. Zebra’s maker documentation establishes the ZC100’s single-sided printing. The ZC300 listing explicitly identifies its double-sided configuration. Ask the seller to confirm anything not stated before placing an order.
| Buying decision | ZC100 LT kit | ZC300 ZC32-000C000US00 |
|---|---|---|
| Exact Amazon purchase | ZC100 LT package | ZC300 USB/Ethernet printer |
| Printing sides | Single-sided, per Zebra’s ZC100 specification | Double-sided, per the listing title |
| Design software | CloudBadging named. License term and edition not stated | CardStudio use mentioned. Included license not stated |
| Starter supplies | Cards and ribbon named. Quantities not stated | Ribbon and blank-card pack not confirmed |
| Network connection | Ask for the exact installed configuration | USB and Ethernet named in the listing title |
| Main buying condition | Confirm software duration and exact refill requirements | Add compatible software, ribbon, cards and cleaning supplies |
The Amazon LT listing describes a ZC100 LT package with CloudBadging software, blank cards and a ribbon. Consider it when you want a supplier to provide the main parts together. An office issuing ordinary photo badges on the front of a card is a reasonable starting use, provided the included software fits its records.
Zebra’s ZC100 specification sheet describes single-sided printing at 300 dpi. Use that maker specification when assessing the printer. Do not choose this package on the assumption that the LT name establishes a higher-resolution printer or automatic duplex hardware.
Ask the seller to identify the actual connections fitted to the unit. Zebra lists USB as standard on the ZC100 and Ethernet or Wi-Fi as options. The family options do not establish that a particular LT kit has either network option. If staff need network printing, include the installed connection in your purchase request.
The limits are package detail and ongoing software use. The Amazon description does not state the blank-card quantity, ribbon yield or CloudBadging license duration. Ask for an itemized contents list and the software terms. Do not count an unnamed duration as a permanent license simply because software appears in the kit title.
Keep the LT identity on later supply orders. Use the ZC100 supply guide ZC100 Supplies: Standard and LT Ribbons Are Separate Choices for the distinction between standard and LT refill listings. A seller should confirm the exact replacement ribbon for the delivered unit before you substitute a standard ZC100 cartridge.
The linked Amazon ZC300 names ZC32-000C000US00, with double-sided printing, USB and Ethernet. Keep that complete number on the order. A generic ZC300 name is insufficient to confirm the same configuration on another offer.
Choose the confirmed duplex unit when staff regularly print information on the reverse. Automatic card turning avoids arranging a separate manual reinsertion step for each side. The benefit depends on your badge design and work pattern, so do not buy duplex hardware solely because it is available.
The listing describes card design and issuance when the printer is used with CardStudio. It does not state that a CardStudio license comes with the printer. No ribbon, blank cards or cleaning supplies are confirmed either. Treat the purchase as hardware and prepare the remaining parts before expecting to issue badges.
Ethernet is confirmed for this unit, but the software arrangements still need a separate check. Ask whether your application permits the intended users and computers. Decide who will maintain the templates and printer settings. A network connection does not establish that a single software license covers every person who needs to print.
The limit for a first-time buyer is the additional setup. An office retaining a compatible design program may prefer the exact hardware configuration. An office starting from nothing should compare the complete purchase with a properly documented kit. Use the ZC300 supply guide Zebra ZC300 Supplies: Choose the Right Ribbon, Cards and Cleaning Kit for ribbon and maintenance choices.
Zebra’s ZC300 specification sheet publishes 200 cards per hour for single-sided YMCKO and 140 cards per hour for dual-sided YMCKOK. YMCKO describes color panels, resin black and clear overlay. YMCKOK includes a second black panel for the reverse-side printing arrangement. The side and ribbon conditions are part of the speed claim.
Zebra bases those rates on USB batch printing and says computer configuration can affect times. Do not use the single-sided rate to promise completion of a dual-sided job. Do not treat either rate as an observed Ethernet result or the time needed to prepare all employee records.
For a school or office batch, plan the work before applying a printer rate. Confirm the final card design and the staff list, then allow time for correcting photographs or records. A supplier’s maximum printer rate cannot establish how quickly your administrator completes the whole job.
Start with the finished front and back design. If all required information fits on the front, a single-sided purchase may meet the job. If the reverse is printed regularly, compare a confirmed automatic dual-sided configuration. Avoid buying based on the broad family name alone.
Specify black or full-color reverse-side artwork before asking for a ribbon. A dual-sided printer and a suitable ribbon are separate requirements. Use the single-sided and dual-sided guide Single-Sided vs Dual-Sided ID Card Printers: When Is Automatic Duplex Worth It? to decide whether automatic card turning fits your work.
Ask for the software name, edition and license duration in writing. The LT package names CloudBadging without a stated term. The linked ZC300 mentions CardStudio use without a stated included license. Neither description gives you enough information to assume unlimited future software use.
Check your current computer and required data imports separately. Tell the supplier whether staff will enter one record at a time or import an employee list. Confirm how photographs are associated with records. A printer driver lets the computer communicate with hardware, while your design application determines how staff prepare badges.
Zebra’s ZC100/ZC300 user guide describes standard CR70 and CR80 PVC or PVC composite cards, 10 to 40 mil thick, for the series. Match the complete card specification to the actual unit and intended print method. A listing for plastic cards without a thickness and material gives you too little information to confirm suitability. Zebra’s specification sheet names the smaller size “CR79”, so order by the user guide’s stated dimensions of 2.051 by 3.303 inches for CR70 and 2.125 by 3.375 inches for CR80.
For a first purchase, get the exact supplied card specification and quantity from the kit seller. For an access credential, also confirm the required chip or magnetic stripe with the system supplier. The printable dimensions do not establish that a plain card can replace an existing encoded credential. Use the blank-card guide CR80 Blank Cards: Choose Thickness, Finish and Material That Fit for that separate purchase decision.
Ask the seller for the replacement ribbon’s complete part number and regional suitability. Zebra’s ZC300 specification sheet says ribbon availability varies by region and describes genuine Zebra ribbons. Retain any LT identification in the replacement request. Similar packaging or a shared Zebra brand is insufficient to establish interchangeability.
Include model-compatible cleaning supplies in the initial order. Zebra’s series user guide describes cleaning the printer and printhead with the appropriate cleaning materials. Follow that procedure rather than assume a starter ribbon covers all maintenance needs. The cleaning process and a supply-brand claim should be checked separately.
Write a short itemized request that another person can approve without interpreting a broad printer title. For the ZC100 LT, ask the seller to confirm these items:
For the ZC300 unit, retain ZC32-000C000US00 and its listed double-sided USB/Ethernet configuration. Add a separately confirmed design license and the matching supplies. Ask for the encoder configuration only if your card system requires one, rather than assume it from the printer’s ability to print on a card with a stripe.
Use the first-system checklist How to Choose Your First ID Badge Printer: A Complete Setup Checklist for the rest of the badge desk. If you want to compare other brands, read the general printer guide Best ID Card Printers. Keep the brand decision separate from the replenishment page so you order supplies for the exact printer you eventually receive.
The Amazon listing names the printer, CloudBadging software, cards and ribbon. You still need confirmation of the software term and supply quantities before calling the package sufficient for your first batch. Ask about cleaning materials wherever the contents do not identify them.
Compare the included software with the job staff need to perform. A kit may contain a designer without establishing the import functions or current computer support you require. Get those answers before deciding that no further purchase is needed.
The linked listing says the printer can be used with CardStudio for card design and issuance. Its description does not establish an included license. Ask the seller to name any included edition and its entitlement, or arrange a separate compatible application.
If your office already owns badge software, check support for the exact printer and the permitted installations. Hardware compatibility and software licensing are separate questions. Ethernet on the printer does not answer either question by itself.
A printer purchase does not establish a working access credential. Zebra’s series guide describes encoding options, and the exact installed encoder must match the card and access system. Ask your access-system supplier to specify the required technology before ordering.
Printing an employee photograph and programming a credential are different jobs. Keep both requirements on the order if you need both. For visual identification alone, choose the printer by its documented sides, connections and package contents, then check the current price on Amazon.