Address
304 North Cardinal St.
Dorchester Center, MA 02124
Work Hours
Monday to Friday: 7AM - 7PM
Weekend: 10AM - 5PM
Understand Fargo DTC4500e error 97, follow HID ribbon calibration and damage checks, and confirm the exact ribbon before ordering a replacement.
This post may contain affiliate links. As an Amazon Associate we earn from qualifying purchases, at no extra cost to you. Learn more.
If your Fargo DTC4500e reports error 97, HID’s user guide calls it Ribbon Search Error. The documented meaning is that the ribbon cannot find the next panel correctly. HID tells you to check for jams or breaks and lists ribbon-sensor calibration, repair of a broken ribbon and ribbon replacement among the remedies.
A new ribbon can belong in this troubleshooting branch, but error 97 does not simply mean the ribbon is empty. HID uses a separate Ribbon Out message for exhaustion. Start with the actual number and message before deciding which supply to order.
The guidance below follows HID’s DTC4500e user guide, PLT-01669 revision 1.1, a maker-authored manual hosted by a distributor. It documents the error meanings and calibration procedure. This page describes those instructions, without hands-on claims or a guarantee that replacing a ribbon will fix a sensor or mechanical fault.
HID’s troubleshooting table describes error 97 as a failure to locate the next ribbon panel correctly. Its cause column also tells the operator to check for jams and breaks. The solution column lists recalibration of the ribbon sensor, taping a broken ribbon back onto the take-up core and replacing the ribbon.
The table gives Pause as the control to continue and ON/OFF as the control to cancel. Keep those actions tied to the error procedure. Continuing a job is not itself evidence that the underlying cause has been corrected.
If you arrived here after seeing wording such as “Check Ribbon,” use the error number to match the manual. The verified guide names 97 Ribbon Search Error. It does not establish “Check Ribbon” as the formal name of that numbered condition, so this page does not treat that wording alone as a diagnosis.
HID’s table distinguishes several errors that can all lead an operator to inspect the ribbon. The number helps you avoid using a replacement intended for one condition as a universal answer to another.
| HID error | Meaning given by the maker | Documented response |
|---|---|---|
| 91, Ribbon Out | The ribbon has run out | Install a new ribbon, then continue or cancel with the stated controls |
| 93, Wrong Ribbon | Installed ribbon differs from the ribbon type selected in the driver | Change the installed ribbon or the selected driver type |
| 97, Ribbon Search Error | Ribbon cannot locate the next panel correctly | Check jams and breaks, recalibrate, repair a break or replace ribbon |
| 99, Ribbon Error | Ribbon has broken or jammed | Clear a jam or tape the broken ribbon onto the take-up core |
| 100, Ribbon RFID Error | No ribbon is present, or ribbon-tag information is corrupted or incorrect | Verify the driver ribbon setting and try a new ribbon |
| 109 or 113, Ribbon Release Error | Printer cannot locate the next panel to release ribbon from the card | Check for ribbon stuck to the card, then follow replacement, calibration or broken-ribbon guidance |
The table does not make a cleaning kit the prescribed fix for 97. It also does not say every ribbon message needs the same cartridge. Identify the branch first, then check the ribbon type and exact replacement reference.
For error 97, HID explicitly says to check for ribbon jams and breaks. Use that as the first physical distinction. An intact ribbon that cannot locate a panel and a visibly broken ribbon are different observations, even though the same error can lead you to inspect both.
HID’s repair instruction for a broken ribbon is to tape it back onto the take-up core. The guide does not specify a particular tape product or make an Amazon tape purchase part of the remedy. It also does not provide a universal dismantling procedure for a ribbon tangled in inaccessible components. Use technical support when the table’s instructions do not cover the problem.
HID’s Calibrate Ribbon section supplies a specific Toolbox procedure. Remove the ribbon cartridge, close the printer’s front cover, select the Calibrate Ribbon tab and click Calibrate. These preparation steps are part of the maker’s procedure, not optional details to skip while leaving the cartridge in place.
The guide identifies Toolbox as the route to Configuration, Calibrate Ribbon, Clean Printer and Advanced Settings. Choose the named calibration function. A cleaning command has a different purpose and does not substitute for the calibration HID prescribes for a panel-search error.
After the applicable remedy, HID’s 97 entry says to press Pause to continue or ON/OFF to cancel. Its table does not add a mandatory restart sequence for every occurrence of 97. Follow the relevant message rather than combining reset instructions from unrelated errors.
When problems go beyond the error table, HID’s troubleshooting guidance directs the operator to technical support. Repeated replacement purchases are not a documented substitute for that escalation. A new cartridge cannot be assumed to repair every condition that prevents panel detection.
For clarity, HID’s section 4.4 gives the calibration preparation and command in this order:
HID says the button sends the Calibrate Ribbon command to the printer. Use the installed software’s instructions with the guide. The documented function is sensor calibration, rather than a change to your badge artwork or card stock.
The manual separately identifies factory-set head and flipper offsets that should not be changed unless a technician directs you. Do not turn a calibration request into trial-and-error changes to those values. The error 97 remedy does not instruct you to change head-home or flipper-home offsets.
Ribbon replacement is explicitly listed in HID’s error 97 solution column. That supports considering a replacement as part of the matching troubleshooting branch. It does not prove that any cartridge carrying the Fargo brand is the correct part, or that replacement is the only remedy.
HID’s installation section describes a one-piece disposable ribbon cartridge for the DTC4500e and says to use Fargo-certified supplies. It also recommends printer cleaning with each ribbon change. That maintenance instruction belongs to installing a replacement. It is not evidence that a cleaning kit independently cures error 97.
Keep the actual installed part number and ribbon type in the purchasing decision. A full-color cartridge, a half-panel cartridge and a monochrome cartridge serve different layouts. Replacing a damaged item should preserve the intended job requirements rather than introducing a different panel arrangement because a listing appears under the same printer family.
The 45200 YMCKO ribbon listing names Fargo Genuine YMCKO Color Ribbon #45200 for Model DTC4500e Printer. Amazon’s listing identifies 45200 and states DTC4500e compatibility. An active New offer was checked on October 1, 2026. The listing’s identity and compatibility statements are seller descriptions, not an independent authentication of the cartridge’s origin.
Use this link only when 45200 is the exact existing or supplier-confirmed replacement reference for your printer and job. Do not treat the model name in the title as permission to ignore regional requirements or changes in the supply generation. Ask the supplier to resolve an unclear replacement code before ordering.
HID’s revised DTC4500e consumables sheet lists 045230 for full-panel YMCKO and warns that part numbers can vary by region. That sheet does not establish that the linked 45200 is the same product as 045230 or that one is an automatic substitution for the other.
For that reason, this page does not assign the current sheet’s yield to the Amazon 45200 item. It also does not promise that changing supply generation will cure error 97. Use DTC4500e Supply Shopping: Start with the Exact 45200 Ribbon when you need the broader part-number comparison.
HID’s ribbon-installation procedure says to open the indicated drawer, insert the ribbon cartridge and close the front cover. Use the diagram in the DTC4500e guide to identify the drawer and cartridge position. The instruction is specific to this model’s cartridge system.
The manual recommends cleaning at ribbon changes. Follow its cleaning procedure with the required supplies if carrying out that maintenance. This page links only the ribbon because the error 97 branch calls for ribbon-related remedies, while the accompanying cleaning recommendation does not make an aftermarket kit a verified error-specific fix.
If the printer instead reports 93, Wrong Ribbon, HID says to change either the installed ribbon or the type selected in the driver. Check that separate condition against the installed cartridge. It does not follow that every Wrong Ribbon report requires discarding a usable cartridge when the mismatch is in the selected type.
HID defines 97 as failure to find the next panel correctly. Its checklist includes jams and breaks, and its remedies include sensor calibration and replacement. Exhaustion has a different number, 91, Ribbon Out.
A replacement may still be appropriate under the 97 branch, but do not infer exhaustion from the number alone. Matching the condition preserves the option of the documented free calibration check before a supply purchase.
HID recommends printer cleaning with each ribbon change, so cleaning supplies may belong in your regular maintenance plan. Its error 97 solution column, however, specifies ribbon and sensor remedies rather than a cleaning-kit cure.
Use the printer’s cleaning instructions and exact compatible supplies for that separate maintenance task. Do not expect the presence of a cleaning kit in an order to establish why panel detection failed or guarantee that the replacement ribbon will work.
The revised HID sheet lists 045230, while the linked Amazon offer identifies 45200. The checked sources do not establish automatic interchangeability or the regional and update requirements for switching between them.
Confirm the replacement with a supplier who can match the installed printer and existing supply. If that confirmation is unavailable, look for the exact approved reference and leave the purchase unresolved rather than treating two different numbers as identical.