Address
304 North Cardinal St.
Dorchester Center, MA 02124
Work Hours
Monday to Friday: 7AM - 7PM
Weekend: 10AM - 5PM
Diagnose Fargo DTC1250e card jams using HID feed, stock and cleaning checks before deciding whether the specified cleaning kit is needed.
This post may contain affiliate links. As an Amazon Associate we earn from qualifying purchases, at no extra cost to you. Learn more.
A Fargo DTC1250e that will not feed a badge needs a different check from one holding a card inside the print station. Start with the exact message shown on your computer. HID separates Unable to Feed, Multiple Feed and Card Jam/Align errors in its troubleshooting table. That distinction helps you choose the relevant procedure before ordering supplies.
HID’s first feed checks are card thickness, the cleaning roller, card slippage, accepted card size and cards sticking together. Cleaning belongs in the slippage branch. A new ribbon is not HID’s general answer to an ordinary card jam.
The steps below follow HID’s DTC1250e user guide, PLT-01668 version 1.2, a maker-authored manual hosted by a distributor. It covers several Fargo models, so use the DTC1250e instructions and your installed options. These are documented procedures, not hands-on results or a promise that cleaning will repair a mechanical fault.
HID’s error table in sections 5.2.2 and 5.2.3 distinguishes the following conditions. Read the message and number together rather than treating every stopped badge as the same fault.
| HID message | Meaning in the manual | Maker’s next action |
|---|---|---|
| 81, Unable to Feed | A card cannot feed from the input hopper | Check thickness, roller installation, slippage, size and sticking cards |
| 70, Multiple Feed | More than one card has fed into the printer | Check thickness, slippage, roller installation and sticking cards |
| 68, Card in Printer | A card is jammed in the print station or flipping area | Clear the jam and press Pause |
| 110 or 112, Card Jam/Align error | A card is jammed in the print station or flipping area | Clear the jam and press Pause to continue |
| 82, Mag Jam | A card is jammed in the magnetic station | Use the buttons to move the card out, then press Pause |
| 131, Flipper Jam/Home Error | A card is jammed in the flipper table or the table has not positioned correctly | Move the card out with the buttons, resume, then follow the reset/support branch if needed |
These meanings matter when buying a replacement supply. Error 81 points first toward feed checks. Error 82 concerns the magnetic station on an equipped printer. Neither identifies an exhausted ribbon. HID gives ribbon exhaustion its own message, 91, Ribbon Out.
For faults beyond the table’s procedures, HID directs owners to technical support. The manual’s instruction to clear a jam does not supply a universal dismantling method for every possible card position. Use the model’s controls and support guidance when the card cannot be cleared through the documented procedure.
For error 81 or 70, HID tells you to verify that the card thickness setting matches the cards being used. Its specifications accept 9 to 40 mil card thickness and identify CR80 and CR79 sizes. Compare the stock’s documented thickness and size with those limits and the printer setting. A card that looks like your usual badge is not sufficient identification.
HID explicitly includes accepted card size in the Unable to Feed checklist. That makes size a relevant diagnostic check, but does not establish that every feeding failure requires new stock. If your existing cards meet the specification, continue through the remaining checks instead of replacing a whole box based on the error alone.
HID’s checklist for Unable to Feed and Multiple Feed includes verifying that cards are not sticking together. Treat this as a separate check from the thickness setting. Matching the nominal thickness does not answer whether two cards are entering together.
HID’s loading procedure also says not to run cards with a contaminated, dull or uneven surface through the printer. It warns that such surfaces can harm print quality and reduce printhead life. Keep unsuitable stock out of the job. The manual does not prescribe household powders, solvents or improvised surface treatments to make those cards usable.
For both feed errors, HID says to verify that the cleaning roller is properly installed on the ribbon cartridge. Check that assembly against the manual before deciding the printer needs a new ribbon. An installation problem and an exhausted ribbon are different conditions in HID’s guidance.
The same error table tells you to look for card slippage and run the printer cleaning routine if necessary. That is the documented reason to move from free checks to cleaning supplies. The kit is relevant when carrying out that routine, rather than as an automatic purchase attached to any card-jam message.
HID’s section 2.4 specifies loading cards with the print side down. For magnetic-stripe cards, the stripe goes up and toward the front of the printer. The procedure starts by opening the input hopper door and pressing the hopper load lever down until the tray locks into place.
The guide then allows up to 100 cards in the input hopper and tells you to close the door to release the lever into the printing position. Follow that loading sequence rather than assuming the hopper is ready simply because cards are visible inside it. The published capacity is not an instruction to overfill the hopper.
For single-feed operation, HID says to remove all cards from the input hopper, leave its door closed and place a card in the single-feed slot. This is a documented operating mode. It is not proof that bypassing a troublesome hopper has repaired it, and it should not replace the appropriate feed-error checks for batch operation.
For 68, 110 and 112, HID says to clear the jam and press Pause. For 82, it specifically says to use the buttons to move cards out of the magnetic station and then press Pause. Keep those instructions tied to the reported location. Moving a card out of one station does not diagnose a fault in another.
For 131, HID says to clear cards in the flipper table using the buttons, resume printing, and reset and retry if required. If the problem persists, its instruction is to call for technical assistance. That escalation is more useful than repeatedly buying ribbons for a table-positioning fault.
HID’s safety section requires qualified personnel for repair procedures and says to remove the power cord before repairs unless otherwise specified. It also requires precautions against static discharge near the printhead and circuit assemblies. Treat repairs as a separate task from an ordinary operator cleaning cycle. This guide does not add an unsupported method for pulling, levering or dismantling a trapped card.
HID’s section 4.1.1.4.3 says card-feed rollers move the card throughout printing and should stay clean to prevent jams and contamination. It describes the following procedure for the platen and feed rollers. Follow the prompts in your installed driver as well as the manual.
The magnetic-encoder exception is part of the procedure, not an optional cosmetic detail. Removing every liner on every printer would miss HID’s protection instruction. Use the cleaning card specified for the procedure rather than treating an ordinary blank badge as a substitute.
This manual describes roller cleaning at approximately 1,000 prints for consistent quality and recommends printer cleaning with each ribbon change in its installation section. Those are maintenance instructions. They do not guarantee that a cleaning cycle will clear every jam or repair damaged hardware.
HID’s cleaning-kit compatibility page identifies 086177 for the DTC1250e. HID lists four printhead swabs, ten cleaning cards and three alcohol cleaning cards. Match the required cleaning card to the procedure rather than using a printhead swab as a replacement for the feed-roller cycle.
The 086177 cleaning-kit offer is titled Card Imaging Fargo Cleaning Kit 86177 for All DTC Printers, Pack of 2. Amazon’s listing describes the Fargo identity and two-pack. Its active New offer was checked on October 1, 2026. Match the part number and package contents before ordering. Seller wording alone does not independently authenticate OEM origin.
Use this purchase route when HID’s slippage check leads to the cleaning routine and you lack the required supplies. There is no linked ribbon, replacement printer or generic blank-card pack here because the ordinary card-jam branch does not prescribe those products as its fix. For a wider replenishment order, read Fargo DTC1250e Supplies: Ribbons, Cards and Cleaning Kits That Fit.
HID’s Card Jam/Align entries tell you to clear the jam and press Pause. Its feed entries specify stock, thickness, roller installation and cleaning checks. Those instructions do not make a new ribbon the default answer to a card jam.
Ribbon-related messages have separate meanings. HID’s Ribbon Out entry calls for a new ribbon, while its ribbon-release entries include checking whether ribbon is stuck to the card. Use the actual message before choosing that separate troubleshooting path.
HID says the cleaning procedure cleans the platen and feed rollers, and includes cleaning where card slippage requires it. That supports carrying out the routine, but it does not establish a diagnosis for every stopped card.
If the matching error continues beyond the manual’s checks, follow HID’s technical-support direction. Keep the error number and the relevant procedure together when explaining the problem, so the next decision concerns the unresolved fault rather than another general supply order.